
Tubing Tool
- The material acts as a Band Pass Filter using physics to drive chemistry. It absorbs the energy and frequency of ambient temperature and pressure. It then reflects or emits a different frequency, acting as a catalyst for chemical changes to occur in oil and water.
- The tubing tool should be installed as deep as possible so it can condition the oil and water before they undergo temperature and pressure drops which change the fluids’ composition and which the tool is unable to reverse.
- The tubing tool consists of the material located around the outside of a standard 4’ API tubing sub and protected by a shroud.
- Multiple tubing tools can be madeup to increase BOPD capacity.
- The tubing tools are offered with a nickel coating for corrosive environments.
- Installation location of the tubing tool is dependent on well candidate design.
Tubing Size (in) | Product Name | Treatment Capacity | Max O.D. (Dim.A)(in) | Drift I.D. (in) |
---|---|---|---|---|
2 3/8 | Ultra-Mini Tubing Tool | <10 BOPD | 3.500 | 1.901 |
2 3/8 | Mini Tubing Tool | <20 BOPD | 3.500 | 1.901 |
2 3/8 | Standard Tubing Tool | <30 BOPD | 3.500 | 1.901 |
2 7/8 | Ultra-Mini Tubing Tool | <12 BOPD | 4.250 | 2.347 |
2 7/8 | Mini Tubing Tool | <23 BOPD | 4.250 | 2.347 |
2 7/8 | Standard Tubing Tool | <35 BOPD | 4.250 | 2347 |
3 1/2 | Standard Tubing Tool | <70 BOPD | 5.250 | 2.867 |

The Strainer Tool Assembly
- The material acts as a Band Pass Filter using physics to drive chemistry. It absorbs the energy and frequency of ambient temperature and pressure. It then reflects or emits a different frequency, acting as a catalyst for chemical changes to occur in oil and water.
- The Strainer Tool Assembly should be installed as deep as possible so it can condition the oil and water before they undergo temperature and pressure drops which change the fluids’ composition and which the tool is unable to reverse.
- The Strainer Tool Assembly includes the Strainer, Trim Tool(s) and Nose Cone.
- Trim Tools consists of a thin walled tube with the the material located inside.
- The Trim Tools are offered with a nickel coating for corrosive environments.
- The Assembly is screwed into the bottom of the insert pump.
- Multiple Trim Tools can be madeup to increase BOPD capacity.
- Trim Tools can also be installed in conjunction with other tool types to increase BOPD capacity.
Trim Tool | Accessories / Expendables | |||
---|---|---|---|---|
Product Name | Treatment Capacity | Dimensions | Product Name | Dimensions |
10” Standard Trim Tool | <5 BOPD | 1.500" x 10" | 1”x10” Strainer | 1.315” x 10” |
16” Standard Trim Tool | <12 BOPD | 1.500" x 16" | 1”x24” Strainer | 1.315” x 24“ |
28” Standard Trim Tool | <20 BOPD | 1.500" x 28" | 1 1/4”x24” Strainer | 1.660” x 24” |
48” Standard Trim Tool | <40 BOPD | 1.500" x 40" | Standard Connector | OD - 1.50” |
Standard Nose Cone | OD - 1.50” |
SLICK LINE TOOL ASSEMBLY

- The material acts as a Band Pass Filter using physics to drive chemistry. It absorbs the energy and frequency of ambient temperature and pressure. It then reflects or emits a different frequency, acting as a catalyst for chemical changes to occur in oil and water.
- For the Slickline Tool Assembly tool to run effectively, it must be installed as deep as possible so it can condition the oil and water before the fluids’ compositions change due to temperature and pressure drops.
- The Slickline Tool Assembly consists of a J fish neck, Trim Tools(s), and a Seating Assembly sized for the correct seating nipple.
- Other configurations of the assembly are available depending on specific well conditions.
- The Slickline Tool Assembly is installed using the 2” J Soft Release running tool.
- Multiple Trim Tools can be made-up to increase BOPD capacity.
- Trim Tools are offered with a nickel coating for corrosive environments.
- The Slickline Tool Assembly can also be installed in conjunction with other tool types to increase capacity.
Trim Tools | Accessories | |||
---|---|---|---|---|
Product Name | Treatment Capacity | Dimensions | Product Name | Dimensions |
10” Standard Trim Tool | <5 BOPD | 1.5" x 10" | 1” Fish Neck (used for 2 3/8 & 2 7/8) | Standard |
16” Standard Trim Tool | <12 BOPD | 1.5" x 16" | Standard Connector | OD - 1.50” |
28” Standard Trim Tool | <20 BOPD | 1.5" x 28" | 2 3/8 Fluted Seating Assembly | Standard |
48” Standard Trim Tool | <40 BOPD | 1.5" x 48" | 2 7/8 Fluted Seating Assembly | Standard |
48” XL Trim Tool | <50 BOPD | 2.0" x 48" | XL Connector | OD - 2.00” |
Running Tool: 2” J Soft Release | Standard | |||
Pulling Tool: 1-3/8” JDC | Standard |